Shapescaper Square Galvabond 500(H)x800x800mm
$566.00 each
Available
Please note Whilst all care has been taken to provide you with a good indication of colour, you should always sight product samples before use, due to natural variations in Colours & Sizes. Products may vary from image provided.
- Supplier Shapescaper
- num_m2 0
Description
The wide range, commercial quality and ease of installation make SHAPESCAPER modular steel planter boxes a preferred choice in garden design for both professional and DIY landscapers.
The planter range is available in either a 500mm or 700mm profile with both profile heights featuring smooth rounded edges with a 40mm x 20mm return top edge for added strength and safety. SHAPESCAPER steel planter boxes are typically supplied without bases to allow for free draining. Planters can be supplied with custom bases and feet suitable for rooftop and patio installations.
SHAPESCAPER steel planters are supplied in two easily joined halves, this allows for compact transport and single handed installation making the SHAPESCAPER range of customisable planters the perfect landscaping design solution for even the most complex builds. SHAPESCAPER planters are self supporting with installation completed by simply aligning the predrilled holes and then securing the supplied fasteners.
Additional information
| Weight | 37.11 kg |
|---|---|
| Dimensions | 800 × 800 × 500 mm |
| Supplier | |
| Application |
DIY Videos
Installation Guide
1. Site Selection and installation: Ring planters are typically installed on level ground, a flat smooth surface will make the the alignment of the ring planter sections prior to riveting together much easier. Line up the section pieces so the holes match up. A light tap with a rubber hammer can help ease the ring’s edging lip over the connector section; a small drift or 4mm pin punch can also help align the holes especially on large profile rings. Simply insert the supplied rivets straight through edging ring and the aligned connector. Secure the top rivet first; ensuring that the ring and connectors is flush. Then secure the bottom rivets, Complete the process by securing middle rivets. If possible working on joining a ring is made much easier if the ring is tipped on it’s side and then pressure applied directly downward while squeezing off the rivets until they pop. Ring planters can be set into sloping ground by first levelling out a base and back filling. Coating all surfaces that are in contact with soil with a waterpoofing treatment such as Crommelin Blackseal Heavy Duty bitumen paint will greatly increase the service life of your ring planter and is highly recommended.
2. Developing a Protective Patina: The weathering steel used in SHAPESCAPER Redcor products will begin forming its protective rust “patina” over a couple of weeks and become fully weathered between 6 months and two years, depending on the exposure to moisture. Please note the use of strong acid or salt to accelerate the process will permanently damage the protective properties of weathering steel. While the patina is forming “rust coloured” run off may occur, care should be taken around porous surfaces travertine pavers and cement. Any leaching should be removed promptly, staining should be dispersed regularly by hosing the area clean, a light spraying of the weathering steel with water will also help speed up the patina process at the same time. A mild 10% solution of white vinegar applied to the run off area prior to washing down can be used for heavier staining.
3. Care of Galvanised Steel Rings: The galvanised steel used in SHAPESCAPER Galvabond products is essentially maintenance free. Care however should be taken not to accidentally remove the protective zinc coating with sharp tools. The mild acids in some garden sprays can also damage the protective zinc coating, any overspray should be promptly removed with using fresh water. Over time the bright metal finish of a newly installed galvanised steel ring will develop a muted soft grey finish.
4. Proper Drainage: Ensure the planter has adequate drainage to prevent water logging. You can add a layer of gravel or small rocks at the bottom before adding soil. This not only improves drainage but also helps aerate the roots, promoting healthier plant growth.
5. Securing Large Rings: While the majority of SHAPESCAPER standard rings are self supporting large diameter rings over 2400mm may need appropriate stakes for additional support especially when installing higher profiles. Two stakes per 2400mm arc is usually sufficient.
$566.00 each
